howto:dumldore
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision | ||
|
howto:dumldore [2017/07/26 18:16] quad808 [Using DUMLdore] |
howto:dumldore [2018/01/19 16:50] (current) digdat0 added mavic to unlock |
||
|---|---|---|---|
| Line 12: | Line 12: | ||
| * Remote Control | * Remote Control | ||
| * Mavic | * Mavic | ||
| + | * Spark | ||
| * Goggles | * Goggles | ||
| * DJI | * DJI | ||
| ===== Using DUMLdore ===== | ===== Using DUMLdore ===== | ||
| + | |||
| + | As of 2.11 incorporates DUMLRacer to allow downgrading of Mavic FW 1.04.0100 | ||
| * **DOWNLOAD THE ENTIRE ZIP FILE NOT JUST THE EXE** | * **DOWNLOAD THE ENTIRE ZIP FILE NOT JUST THE EXE** | ||
| * Make sure you have at least 50% battery remaining before you begin | * Make sure you have at least 50% battery remaining before you begin | ||
| * Make sure Assistant2 is not running | * Make sure Assistant2 is not running | ||
| - | * Turn on your device (Aircraft | + | * Turn on your device (Aircraft / Goggles) and allow it to fully start up before connecting to PC. (Wait about 30-60 seconds) |
| - | * Plug in USB cable from the aircraft/RC to the PC. Make sure you are using a good DATA cable, NOT a phone charging cable. | + | * Plug in USB cable from the aircraft to the PC. Make sure you are using a good DATA cable, NOT a phone charging cable. Power on the RC AFTER connecting it to the PC for it to be detected properly. |
| * Start DUMLdore.exe | * Start DUMLdore.exe | ||
| * Confirm connectivity | * Confirm connectivity | ||
| Line 28: | Line 31: | ||
| * Once Assistant detects your device, CLOSE assistant before running DUMLdore | * Once Assistant detects your device, CLOSE assistant before running DUMLdore | ||
| * **Using DUMLdore** | * **Using DUMLdore** | ||
| - | * **LOAD**: Will load a firmware file for flashing. Some error checking is done to make sure it is valid. It is not perfect and up to the user to make sure it is. After pointing to the correct | + | * **LOAD**: Will load a firmware file for flashing. Some error checking is done to make sure it is valid. It is not perfect and up to the user to make sure it is. After pointing to the correct |
| * **FLASH**: Uploads the firmware file in the Load step to the device and begins the upgrade/ | * **FLASH**: Uploads the firmware file in the Load step to the device and begins the upgrade/ | ||
| * **BACKUP**: Will make a flashable firmware backup of the currently connected device if applicable. It will save the dji_system.bin file into the current directory. It may take some time. Please be patient as the status may take a few moments to update on some of the files. If you are making a backup of your aircraft and your remote controller, rename or move the 1st backup file into a folder before running the backup on the next device. | * **BACKUP**: Will make a flashable firmware backup of the currently connected device if applicable. It will save the dji_system.bin file into the current directory. It may take some time. Please be patient as the status may take a few moments to update on some of the files. If you are making a backup of your aircraft and your remote controller, rename or move the 1st backup file into a folder before running the backup on the next device. | ||
| - | * **OPTIONAL** this step is for error checking so repeat | + | * **UNLOCK**: Will unlocked a grounded Spark OR Mavic due to not performing |
| + | * **ACTIVATE MAVIC**: Offline activation of Mavic | ||
| ===== Firmware ===== | ===== Firmware ===== | ||
howto/dumldore.1501092976.txt.gz · Last modified: 2017/07/26 18:16 by quad808
Page Tools
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Noncommercial-Share Alike 4.0 International
