Differences

This shows you the differences between two versions of the page.

--- howto:modp3params [2018/06/12 02:26]
digdat0 [Important Parameter Descriptions]
+++ howto:modp3params [2019/07/21 23:35] (current)
digdat0 [Parameter Values to Change]
@@ Line 96: / Line 96: @@
   * After this command runs, it will compile the parameters back into the P3X_FW_V01.07.0060_m0306.bin file.
-  * Now, you need to rename the file before loading on the aircraft. Rename it to "PMCAPPFw3.bin" (For Inspire1 rename to "INMCAPPFw1.bin" for FW 01.05->01.09 or "INMCAPPFw1.bin" for FW 01.10 -> 01.11.01.50
+  * Now, you need to rename the file before loading on the aircraft. Rename it to "PMCAPPFw3.bin" for p3 and "INMCAPPFw1.bin" for inspire 1 (no quotes).
 ====  4. Install the modded file on your Phantom ====
-  * To install the file on your Phantom, copy the PMCAPPFw3.bin file to a formatted micro-SD card
+  * To install the file on your aircraft, copy the PMCAPPFw3.bin or INMCAPPFw1.bin file to a formatted micro-SD card
   * Insert SD card into aircraft, power on. If the firmware update does not start, you can force it by holding the button on the side of the VPS.
   * The file will be flashed and the edited parameters will be applied.
@@ Line 113: / Line 114: @@
 ^ Parameter Name ^ Description^
-^ g_config.advanced_function.height_limit_enabled_0|Removes height limit|
+^ advanced_function.height_limit_enabled_0|Removes height limit|
-^ g_config.control.horiz_vel_atti_range_0|GPS Tilt angle makes faster|
+^ control.horiz_vel_atti_range_0|GPS Tilt angle makes faster|
-^ g_config.control.atti_range_0|ATTI Max tilt angle|
+^ control.atti_range_0|ATTI Max tilt angle|
-^ g_config.control.atti_limit_0	| ATTI tilt angle
+^ control.atti_limit_0	| ATTI tilt angle|
-^ g_config.control.vert_up_vel_0|Ascent Velocity Rate (Up)|
+^ control.vert_up_vel_0|Ascent Velocity Rate (Up)|
-^ g_config.control.vert_down_vel_0|Descent Velocity Rate (Down)|
+^ control.vert_down_vel_0|Descent Velocity Rate (Down)|
-^ g_config.airport_limit_cfg.cfg_search_radius_0 | NFZ search radius, lower is less enforcement
+^ airport_limit_cfg.cfg_search_radius_0 | NFZ search radius, lower is less enforcement|
-^ g_config.airport_limit_cfg.cfg_disable_airport_fly_limit_0|Disable NFZ|
+^ airport_limit_cfg.cfg_disable_airport_fly_limit_0|Disable NFZ|
-^ g_config.airport_limit_cfg.cfg_limit_data_0 | NFZ map data value
+^ airport_limit_cfg.cfg_limit_data_0 | NFZ map data value|
-^ g_config.airport_limit_cfg.cfg_enable[FLY_LIMIT_TYPE_SPECIAL]_0 | NFZ Type 2 Removal (GeoZone)
+^ airport_limit_cfg.cfg_enable[FLY_LIMIT_TYPE_SPECIAL]_0 | NFZ Type 2 Removal (GeoZone)|
-^ g_config.flying_limit.auto_landing_enabled_0|No landing at 65k feet from HP|
+^ flying_limit.auto_landing_enabled_0|No landing at 65k feet from HP|
-^ g_config.voltage.level_1_protect_type_0|Battery level 1 function (warn, led)|
+^ voltage.level_1_protect_type_0|Battery level 1 function (warn, led)|
-^ g_config.voltage.level_2_protect_type_0|Battery level 1 function (warn, led, land)|
+^ voltage.level_2_protect_type_0|Battery level 1 function (warn, led, land)|
-^ g_config.voltage2.level_1_voltage_0|Battery level 1 %|
+^ voltage2.level_1_voltage_0|Battery level 1 %|
-^ g_config.voltage2.level_1_function_0|Battery level 1 function (warn, land)|
+^ voltage2.level_1_function_0|Battery level 1 function (warn, land)|
-^ g_config.voltage2.level_2_voltage_0|Battery level 2 %|
+^ voltage2.level_2_voltage_0|Battery level 2 %|
-^ g_config.voltage2.level_2_function_0|Battery level 1 function (warn, land)|
+^ voltage2.level_2_function_0|Battery level 1 function (warn, land)|
-^ g_config.voltage2.user_set_smart_bat_0|Battery type (DJI vs non-DJI)|
+^ voltage2.user_set_smart_bat_0|Battery type (DJI vs non-DJI)|
-^ g_config.voltage2.level2_smart_battert_land_0|SmartRTH battery landing %|
+^ voltage2.level2_smart_battert_land_0|SmartRTH battery landing %|
+^ advanced_function.driver_license_limit_enable_0|DJI Driver License Pilot|
+^ advanced_function.viechle_license_limit_enable_0|DJI Driver License Aircraft|
 ====== Parameter Values to Change ======
 I removed the g_config from the prefix to make the table fit better :)
-Last edit: digdat0 11/06/2018. use the tilt and vert up/down as guidelines.
+Last edit: digdat0 07/21/201. adding license param. use the tilt and vert up/down as guidelines.
 **Height Limit Removal**
@@ Line 171: / Line 174: @@
 ^ voltage2.user_set_smart_bat_0 | 0 | 10 | 2 | 0 | 0 | 0 |
 ^ voltage2.level2_smart_battert_land_0 | 0 | 100 | 10 | 0 | 0 | 0 |
+**Disable DJI's driver license enforcement**
+^ Parameter Name ^ Stock minValue ^ Stock MaxValue ^ Stock defaultValue ^ New MinValue ^ new Maxvalue ^ New defaultValue ^
+^ advanced_function.driver_license_limit_enable_0 | 1 | 1 | 1 | 2 | 2 | 2 |
+^ advanced_function.viechle_license_limit_enable_0 | 1 | 1 | 1 | 2 | 2 | 2 |
+These parameters are intended to be informational and as guidelines. You can change certain ones like speed +/- from what is posted above. Please fly safe and within the limits of the aircraft and yourself.
+====== Finish ======
+Once you are done editing, you can fly. I recommend compass calibration. You ca
 ===== All Parameters Lists =====
   * [[howto:P3C|Phantom 3 Standard - All Parameters]]

User Tools

Site Tools

Differences

Page Tools