howto:modp3params
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision | ||
|
howto:modp3params [2018/06/12 02:26] digdat0 [Important Parameter Descriptions] |
howto:modp3params [2019/07/21 23:35] (current) digdat0 [Parameter Values to Change] |
||
|---|---|---|---|
| Line 96: | Line 96: | ||
| * After this command runs, it will compile the parameters back into the P3X_FW_V01.07.0060_m0306.bin file. | * After this command runs, it will compile the parameters back into the P3X_FW_V01.07.0060_m0306.bin file. | ||
| - | * Now, you need to rename the file before loading on the aircraft. Rename it to " | + | * Now, you need to rename the file before loading on the aircraft. Rename it to " |
| ==== 4. Install the modded file on your Phantom ==== | ==== 4. Install the modded file on your Phantom ==== | ||
| - | * To install the file on your Phantom, copy the PMCAPPFw3.bin file to a formatted micro-SD card | + | * To install the file on your aircraft, copy the PMCAPPFw3.bin or INMCAPPFw1.bin file to a formatted micro-SD card |
| * Insert SD card into aircraft, power on. If the firmware update does not start, you can force it by holding the button on the side of the VPS. | * Insert SD card into aircraft, power on. If the firmware update does not start, you can force it by holding the button on the side of the VPS. | ||
| * The file will be flashed and the edited parameters will be applied. | * The file will be flashed and the edited parameters will be applied. | ||
| Line 132: | Line 133: | ||
| ^ voltage2.user_set_smart_bat_0|Battery type (DJI vs non-DJI)| | ^ voltage2.user_set_smart_bat_0|Battery type (DJI vs non-DJI)| | ||
| ^ voltage2.level2_smart_battert_land_0|SmartRTH battery landing %| | ^ voltage2.level2_smart_battert_land_0|SmartRTH battery landing %| | ||
| + | ^ advanced_function.driver_license_limit_enable_0|DJI Driver License Pilot| | ||
| + | ^ advanced_function.viechle_license_limit_enable_0|DJI Driver License Aircraft| | ||
| ====== Parameter Values to Change ====== | ====== Parameter Values to Change ====== | ||
| I removed the g_config from the prefix to make the table fit better :) | I removed the g_config from the prefix to make the table fit better :) | ||
| - | Last edit: digdat0 | + | Last edit: digdat0 |
| **Height Limit Removal** | **Height Limit Removal** | ||
| Line 171: | Line 174: | ||
| ^ voltage2.user_set_smart_bat_0 | 0 | 10 | 2 | 0 | 0 | 0 | | ^ voltage2.user_set_smart_bat_0 | 0 | 10 | 2 | 0 | 0 | 0 | | ||
| ^ voltage2.level2_smart_battert_land_0 | 0 | 100 | 10 | 0 | 0 | 0 | | ^ voltage2.level2_smart_battert_land_0 | 0 | 100 | 10 | 0 | 0 | 0 | | ||
| + | **Disable DJI's driver license enforcement** | ||
| + | ^ Parameter Name ^ Stock minValue ^ Stock MaxValue ^ Stock defaultValue ^ New MinValue ^ new Maxvalue ^ New defaultValue ^ | ||
| + | ^ advanced_function.driver_license_limit_enable_0 | 1 | 1 | 1 | 2 | 2 | 2 | | ||
| + | ^ advanced_function.viechle_license_limit_enable_0 | 1 | 1 | 1 | 2 | 2 | 2 | | ||
| + | |||
| + | These parameters are intended to be informational and as guidelines. You can change certain ones like speed +/- from what is posted above. Please fly safe and within the limits of the aircraft and yourself. | ||
| + | |||
| + | ====== Finish ====== | ||
| + | Once you are done editing, you can fly. I recommend compass calibration. You ca | ||
| ===== All Parameters Lists ===== | ===== All Parameters Lists ===== | ||
| * [[howto: | * [[howto: | ||
howto/modp3params.1528770398.txt.gz · Last modified: 2018/06/12 02:26 by digdat0
Page Tools
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Noncommercial-Share Alike 4.0 International
