User Tools

Site Tools


howto:modp3params

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
howto:modp3params [2019/07/21 23:20]
digdat0 rewrote install steps
howto:modp3params [2019/07/21 23:35] (current)
digdat0 [Parameter Values to Change]
Line 94: Line 94:
  
    dji_flyc_param_ed.py -vv -u -m P3X_FW_V01.07.0060_m0306.bin    dji_flyc_param_ed.py -vv -u -m P3X_FW_V01.07.0060_m0306.bin
-    
-This will recompile the modified firmware module, which will allow it to be installed onto the aircraft. You can now update the aircraft with this firmware file. 
  
-To install on the aircraft:+  * After this command runs, it will compile the parameters back into the P3X_FW_V01.07.0060_m0306.bin file.  
 +  * Now, you need to rename the file before loading on the aircraft. Rename it to "PMCAPPFw3.bin" for p3 and "INMCAPPFw1.bin" for inspire 1 (no quotes).
  
-1. Rename the modified file P3X_FW_V01.07.0060_m0306.bin 
-    p3 = PMCAPPFw3.bin  
-    I1 = INMCAPPFw1.bin 
-2. Copy the file to your SD card. Put SD card into the aircraft.  
-3. Power on the aircraft. Update will start in about 30 seconds. You will hear a distinct noise during the update process, which will change when done. It should take 3-5 minutes. 
  
-** If the update does not start, please turn off aircraft. Press and hold the bind button, and turn back on. Hold this button for 20-30 seconds and the update will start and will make a beeping noise, then you can let go and let the update finish. 
- 
-4. When update is done, power off the aicraft. Remove the SD card from the camera and back into the computer 
-5. Remove/ Delete the "PMCAPPFw3.bin_updated" or "INMCAPPFw1.bin_updated" file from the SD card 
-  Note: If the file is "PMCAPPFw3.bin_damaged" or "INMCAPPFw1.bin_damaged" the update did not complete, retry it. 
-6. Put Sd card back in the camera  
- 
-All done!  On your next startup, the modifications will persist on the aircraft. They will remain until you reflash the stock firmware.  
- 
-Note: If your firmware is version 01.04 or earlier, you may need to rename the file MCAPPFw.bin instead. 
 ====  4. Install the modded file on your Phantom ====  ====  4. Install the modded file on your Phantom ==== 
-  * To install the file on your Phantom, copy the PMCAPPFw3.bin file to a formatted micro-SD card+  * To install the file on your aircraft, copy the PMCAPPFw3.bin or INMCAPPFw1.bin file to a formatted micro-SD card
   * Insert SD card into aircraft, power on. If the firmware update does not start, you can force it by holding the button on the side of the VPS.   * Insert SD card into aircraft, power on. If the firmware update does not start, you can force it by holding the button on the side of the VPS.
   * The file will be flashed and the edited parameters will be applied.   * The file will be flashed and the edited parameters will be applied.
Line 149: Line 133:
 ^ voltage2.user_set_smart_bat_0|Battery type (DJI vs non-DJI)| ^ voltage2.user_set_smart_bat_0|Battery type (DJI vs non-DJI)|
 ^ voltage2.level2_smart_battert_land_0|SmartRTH battery landing %| ^ voltage2.level2_smart_battert_land_0|SmartRTH battery landing %|
 +^ advanced_function.driver_license_limit_enable_0|DJI Driver License Pilot|
 +^ advanced_function.viechle_license_limit_enable_0|DJI Driver License Aircraft|
 ====== Parameter Values to Change ====== ====== Parameter Values to Change ======
 I removed the g_config from the prefix to make the table fit better :) I removed the g_config from the prefix to make the table fit better :)
  
-Last edit: digdat0 11/06/2018. use the tilt and vert up/down as guidelines.+Last edit: digdat0 07/21/201. adding license param. use the tilt and vert up/down as guidelines.
  
 **Height Limit Removal** **Height Limit Removal**
Line 188: Line 174:
 ^ voltage2.user_set_smart_bat_0 | 0 | 10 | 2 | 0 | 0 | 0 | ^ voltage2.user_set_smart_bat_0 | 0 | 10 | 2 | 0 | 0 | 0 |
 ^ voltage2.level2_smart_battert_land_0 | 0 | 100 | 10 | 0 | 0 | 0 | ^ voltage2.level2_smart_battert_land_0 | 0 | 100 | 10 | 0 | 0 | 0 |
 +**Disable DJI's driver license enforcement**
 +^ Parameter Name ^ Stock minValue ^ Stock MaxValue ^ Stock defaultValue ^ New MinValue ^ new Maxvalue ^ New defaultValue ^
 +^ advanced_function.driver_license_limit_enable_0 | 1 | 1 | 1 | 2 | 2 | 2 |
 +^ advanced_function.viechle_license_limit_enable_0 | 1 | 1 | 1 | 2 | 2 | 2 |
 +
 +These parameters are intended to be informational and as guidelines. You can change certain ones like speed +/- from what is posted above. Please fly safe and within the limits of the aircraft and yourself.
 +
 +====== Finish ======
 +Once you are done editing, you can fly. I recommend compass calibration. You ca
 ===== All Parameters Lists ===== ===== All Parameters Lists =====
   * [[howto:P3C|Phantom 3 Standard - All Parameters]]   * [[howto:P3C|Phantom 3 Standard - All Parameters]]
howto/modp3params.1563751241.txt.gz · Last modified: 2019/07/21 23:20 by digdat0