User Tools

Site Tools


howto:modp3params

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
Next revision Both sides next revision
howto:modp3params [2018/06/12 02:25]
digdat0 [Important Parameter Descriptions]
howto:modp3params [2018/06/12 02:26]
digdat0 [Important Parameter Descriptions]
Line 110: Line 110:
  
 ====== Important Parameter Descriptions ====== ====== Important Parameter Descriptions ======
 +I removed the g_config from the prefix to make the table fit better :)
 +
 ^ Parameter Name ^ Description^ ^ Parameter Name ^ Description^
-g_config.advanced_function.height_limit_enabled_0|Removes height limit| +^ advanced_function.height_limit_enabled_0|Removes height limit| 
-g_config.control.horiz_vel_atti_range_0|GPS Tilt angle makes faster| +^ control.horiz_vel_atti_range_0|GPS Tilt angle makes faster| 
-g_config.control.atti_range_0|ATTI Max tilt angle| +^ control.atti_range_0|ATTI Max tilt angle| 
-g_config.control.atti_limit_0 | ATTI tilt angle +^ control.atti_limit_0 | ATTI tilt angle| 
-g_config.control.vert_up_vel_0|Ascent Velocity Rate (Up)| +^ control.vert_up_vel_0|Ascent Velocity Rate (Up)| 
-g_config.control.vert_down_vel_0|Descent Velocity Rate (Down)| +^ control.vert_down_vel_0|Descent Velocity Rate (Down)| 
-g_config.airport_limit_cfg.cfg_search_radius_0 | NFZ search radius, lower is less enforcement +^ airport_limit_cfg.cfg_search_radius_0 | NFZ search radius, lower is less enforcement| 
-g_config.airport_limit_cfg.cfg_disable_airport_fly_limit_0|Disable NFZ| +^ airport_limit_cfg.cfg_disable_airport_fly_limit_0|Disable NFZ| 
-g_config.airport_limit_cfg.cfg_limit_data_0 | NFZ map data value +^ airport_limit_cfg.cfg_limit_data_0 | NFZ map data value| 
-g_config.airport_limit_cfg.cfg_enable[FLY_LIMIT_TYPE_SPECIAL]_0 | NFZ Type 2 Removal (GeoZone) +^ airport_limit_cfg.cfg_enable[FLY_LIMIT_TYPE_SPECIAL]_0 | NFZ Type 2 Removal (GeoZone)| 
-g_config.flying_limit.auto_landing_enabled_0|No landing at 65k feet from HP| +^ flying_limit.auto_landing_enabled_0|No landing at 65k feet from HP| 
-g_config.voltage.level_1_protect_type_0|Battery level 1 function (warn, led)| +^ voltage.level_1_protect_type_0|Battery level 1 function (warn, led)| 
-g_config.voltage.level_2_protect_type_0|Battery level 1 function (warn, led, land)| +^ voltage.level_2_protect_type_0|Battery level 1 function (warn, led, land)| 
-g_config.voltage2.level_1_voltage_0|Battery level 1 %| +^ voltage2.level_1_voltage_0|Battery level 1 %| 
-g_config.voltage2.level_1_function_0|Battery level 1 function (warn, land)| +^ voltage2.level_1_function_0|Battery level 1 function (warn, land)| 
-g_config.voltage2.level_2_voltage_0|Battery level 2 %| +^ voltage2.level_2_voltage_0|Battery level 2 %| 
-g_config.voltage2.level_2_function_0|Battery level 1 function (warn, land)| +^ voltage2.level_2_function_0|Battery level 1 function (warn, land)| 
-g_config.voltage2.user_set_smart_bat_0|Battery type (DJI vs non-DJI)| +^ voltage2.user_set_smart_bat_0|Battery type (DJI vs non-DJI)| 
-g_config.voltage2.level2_smart_battert_land_0|SmartRTH battery landing %|+^ voltage2.level2_smart_battert_land_0|SmartRTH battery landing %|
 ====== Parameter Values to Change ====== ====== Parameter Values to Change ======
 I removed the g_config from the prefix to make the table fit better :) I removed the g_config from the prefix to make the table fit better :)
howto/modp3params.txt · Last modified: 2019/07/21 23:35 by digdat0