howto:modp3params
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
|
howto:modp3params [2018/06/12 02:25] digdat0 [Important Parameter Descriptions] |
howto:modp3params [2019/07/21 23:24] digdat0 restored |
||
|---|---|---|---|
| Line 96: | Line 96: | ||
| * After this command runs, it will compile the parameters back into the P3X_FW_V01.07.0060_m0306.bin file. | * After this command runs, it will compile the parameters back into the P3X_FW_V01.07.0060_m0306.bin file. | ||
| - | * Now, you need to rename the file before loading on the aircraft. Rename it to " | + | * Now, you need to rename the file before loading on the aircraft. Rename it to " |
| + | * For Inspire1 rename | ||
| ==== 4. Install the modded file on your Phantom ==== | ==== 4. Install the modded file on your Phantom ==== | ||
| Line 110: | Line 111: | ||
| ====== Important Parameter Descriptions ====== | ====== Important Parameter Descriptions ====== | ||
| + | I removed the g_config from the prefix to make the table fit better :) | ||
| + | |||
| ^ Parameter Name ^ Description^ | ^ Parameter Name ^ Description^ | ||
| - | ^ g_config.advanced_function.height_limit_enabled_0|Removes height limit| | + | ^ advanced_function.height_limit_enabled_0|Removes height limit| |
| - | ^ g_config.control.horiz_vel_atti_range_0|GPS Tilt angle makes faster| | + | ^ control.horiz_vel_atti_range_0|GPS Tilt angle makes faster| |
| - | ^ g_config.control.atti_range_0|ATTI Max tilt angle| | + | ^ control.atti_range_0|ATTI Max tilt angle| |
| - | ^ g_config.control.atti_limit_0 | ATTI tilt angle | + | ^ control.atti_limit_0 | ATTI tilt angle| |
| - | ^ g_config.control.vert_up_vel_0|Ascent Velocity Rate (Up)| | + | ^ control.vert_up_vel_0|Ascent Velocity Rate (Up)| |
| - | ^ g_config.control.vert_down_vel_0|Descent Velocity Rate (Down)| | + | ^ control.vert_down_vel_0|Descent Velocity Rate (Down)| |
| - | ^ g_config.airport_limit_cfg.cfg_search_radius_0 | NFZ search radius, lower is less enforcement | + | ^ airport_limit_cfg.cfg_search_radius_0 | NFZ search radius, lower is less enforcement| |
| - | ^ g_config.airport_limit_cfg.cfg_disable_airport_fly_limit_0|Disable NFZ| | + | ^ airport_limit_cfg.cfg_disable_airport_fly_limit_0|Disable NFZ| |
| - | ^ g_config.airport_limit_cfg.cfg_limit_data_0 | NFZ map data value | + | ^ airport_limit_cfg.cfg_limit_data_0 | NFZ map data value| |
| - | ^ g_config.airport_limit_cfg.cfg_enable[FLY_LIMIT_TYPE_SPECIAL]_0 | NFZ Type 2 Removal (GeoZone) | + | ^ airport_limit_cfg.cfg_enable[FLY_LIMIT_TYPE_SPECIAL]_0 | NFZ Type 2 Removal (GeoZone)| |
| - | ^ g_config.flying_limit.auto_landing_enabled_0|No landing at 65k feet from HP| | + | ^ flying_limit.auto_landing_enabled_0|No landing at 65k feet from HP| |
| - | ^ g_config.voltage.level_1_protect_type_0|Battery level 1 function (warn, led)| | + | ^ voltage.level_1_protect_type_0|Battery level 1 function (warn, led)| |
| - | ^ g_config.voltage.level_2_protect_type_0|Battery level 1 function (warn, led, land)| | + | ^ voltage.level_2_protect_type_0|Battery level 1 function (warn, led, land)| |
| - | ^ g_config.voltage2.level_1_voltage_0|Battery level 1 %| | + | ^ voltage2.level_1_voltage_0|Battery level 1 %| |
| - | ^ g_config.voltage2.level_1_function_0|Battery level 1 function (warn, land)| | + | ^ voltage2.level_1_function_0|Battery level 1 function (warn, land)| |
| - | ^ g_config.voltage2.level_2_voltage_0|Battery level 2 %| | + | ^ voltage2.level_2_voltage_0|Battery level 2 %| |
| - | ^ g_config.voltage2.level_2_function_0|Battery level 1 function (warn, land)| | + | ^ voltage2.level_2_function_0|Battery level 1 function (warn, land)| |
| - | ^ g_config.voltage2.user_set_smart_bat_0|Battery type (DJI vs non-DJI)| | + | ^ voltage2.user_set_smart_bat_0|Battery type (DJI vs non-DJI)| |
| - | ^ g_config.voltage2.level2_smart_battert_land_0|SmartRTH battery landing %| | + | ^ voltage2.level2_smart_battert_land_0|SmartRTH battery landing %| |
| ====== Parameter Values to Change ====== | ====== Parameter Values to Change ====== | ||
| I removed the g_config from the prefix to make the table fit better :) | I removed the g_config from the prefix to make the table fit better :) | ||
howto/modp3params.txt · Last modified: 2019/07/21 23:35 by digdat0
Page Tools
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Noncommercial-Share Alike 4.0 International
