This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
howto:modp3params [2018/06/12 02:26] digdat0 [Important Parameter Descriptions] |
howto:modp3params [2019/07/21 23:24] digdat0 restored |
||
---|---|---|---|
Line 96: | Line 96: | ||
* After this command runs, it will compile the parameters back into the P3X_FW_V01.07.0060_m0306.bin file. | * After this command runs, it will compile the parameters back into the P3X_FW_V01.07.0060_m0306.bin file. | ||
- | * Now, you need to rename the file before loading on the aircraft. Rename it to " | + | * Now, you need to rename the file before loading on the aircraft. Rename it to " |
+ | * For Inspire1 rename | ||
==== 4. Install the modded file on your Phantom ==== | ==== 4. Install the modded file on your Phantom ==== | ||
Line 113: | Line 114: | ||
^ Parameter Name ^ Description^ | ^ Parameter Name ^ Description^ | ||
- | ^ g_config.advanced_function.height_limit_enabled_0|Removes height limit| | + | ^ advanced_function.height_limit_enabled_0|Removes height limit| |
- | ^ g_config.control.horiz_vel_atti_range_0|GPS Tilt angle makes faster| | + | ^ control.horiz_vel_atti_range_0|GPS Tilt angle makes faster| |
- | ^ g_config.control.atti_range_0|ATTI Max tilt angle| | + | ^ control.atti_range_0|ATTI Max tilt angle| |
- | ^ g_config.control.atti_limit_0 | ATTI tilt angle | + | ^ control.atti_limit_0 | ATTI tilt angle| |
- | ^ g_config.control.vert_up_vel_0|Ascent Velocity Rate (Up)| | + | ^ control.vert_up_vel_0|Ascent Velocity Rate (Up)| |
- | ^ g_config.control.vert_down_vel_0|Descent Velocity Rate (Down)| | + | ^ control.vert_down_vel_0|Descent Velocity Rate (Down)| |
- | ^ g_config.airport_limit_cfg.cfg_search_radius_0 | NFZ search radius, lower is less enforcement | + | ^ airport_limit_cfg.cfg_search_radius_0 | NFZ search radius, lower is less enforcement| |
- | ^ g_config.airport_limit_cfg.cfg_disable_airport_fly_limit_0|Disable NFZ| | + | ^ airport_limit_cfg.cfg_disable_airport_fly_limit_0|Disable NFZ| |
- | ^ g_config.airport_limit_cfg.cfg_limit_data_0 | NFZ map data value | + | ^ airport_limit_cfg.cfg_limit_data_0 | NFZ map data value| |
- | ^ g_config.airport_limit_cfg.cfg_enable[FLY_LIMIT_TYPE_SPECIAL]_0 | NFZ Type 2 Removal (GeoZone) | + | ^ airport_limit_cfg.cfg_enable[FLY_LIMIT_TYPE_SPECIAL]_0 | NFZ Type 2 Removal (GeoZone)| |
- | ^ g_config.flying_limit.auto_landing_enabled_0|No landing at 65k feet from HP| | + | ^ flying_limit.auto_landing_enabled_0|No landing at 65k feet from HP| |
- | ^ g_config.voltage.level_1_protect_type_0|Battery level 1 function (warn, led)| | + | ^ voltage.level_1_protect_type_0|Battery level 1 function (warn, led)| |
- | ^ g_config.voltage.level_2_protect_type_0|Battery level 1 function (warn, led, land)| | + | ^ voltage.level_2_protect_type_0|Battery level 1 function (warn, led, land)| |
- | ^ g_config.voltage2.level_1_voltage_0|Battery level 1 %| | + | ^ voltage2.level_1_voltage_0|Battery level 1 %| |
- | ^ g_config.voltage2.level_1_function_0|Battery level 1 function (warn, land)| | + | ^ voltage2.level_1_function_0|Battery level 1 function (warn, land)| |
- | ^ g_config.voltage2.level_2_voltage_0|Battery level 2 %| | + | ^ voltage2.level_2_voltage_0|Battery level 2 %| |
- | ^ g_config.voltage2.level_2_function_0|Battery level 1 function (warn, land)| | + | ^ voltage2.level_2_function_0|Battery level 1 function (warn, land)| |
- | ^ g_config.voltage2.user_set_smart_bat_0|Battery type (DJI vs non-DJI)| | + | ^ voltage2.user_set_smart_bat_0|Battery type (DJI vs non-DJI)| |
- | ^ g_config.voltage2.level2_smart_battert_land_0|SmartRTH battery landing %| | + | ^ voltage2.level2_smart_battert_land_0|SmartRTH battery landing %| |
====== Parameter Values to Change ====== | ====== Parameter Values to Change ====== | ||
I removed the g_config from the prefix to make the table fit better :) | I removed the g_config from the prefix to make the table fit better :) |