This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
howto:modp3params [2018/06/12 02:25] digdat0 [Important Parameter Descriptions] |
howto:modp3params [2019/07/21 23:29] digdat0 [Important Parameter Descriptions] |
||
---|---|---|---|
Line 96: | Line 96: | ||
* After this command runs, it will compile the parameters back into the P3X_FW_V01.07.0060_m0306.bin file. | * After this command runs, it will compile the parameters back into the P3X_FW_V01.07.0060_m0306.bin file. | ||
- | * Now, you need to rename the file before loading on the aircraft. Rename it to " | + | * Now, you need to rename the file before loading on the aircraft. Rename it to " |
==== 4. Install the modded file on your Phantom ==== | ==== 4. Install the modded file on your Phantom ==== | ||
- | * To install the file on your Phantom, copy the PMCAPPFw3.bin file to a formatted micro-SD card | + | * To install the file on your aircraft, copy the PMCAPPFw3.bin or INMCAPPFw1.bin file to a formatted micro-SD card |
* Insert SD card into aircraft, power on. If the firmware update does not start, you can force it by holding the button on the side of the VPS. | * Insert SD card into aircraft, power on. If the firmware update does not start, you can force it by holding the button on the side of the VPS. | ||
* The file will be flashed and the edited parameters will be applied. | * The file will be flashed and the edited parameters will be applied. | ||
Line 116: | Line 117: | ||
^ control.horiz_vel_atti_range_0|GPS Tilt angle makes faster| | ^ control.horiz_vel_atti_range_0|GPS Tilt angle makes faster| | ||
^ control.atti_range_0|ATTI Max tilt angle| | ^ control.atti_range_0|ATTI Max tilt angle| | ||
- | ^ control.atti_limit_0 | ATTI tilt angle | + | ^ control.atti_limit_0 | ATTI tilt angle| |
^ control.vert_up_vel_0|Ascent Velocity Rate (Up)| | ^ control.vert_up_vel_0|Ascent Velocity Rate (Up)| | ||
^ control.vert_down_vel_0|Descent Velocity Rate (Down)| | ^ control.vert_down_vel_0|Descent Velocity Rate (Down)| | ||
- | ^ airport_limit_cfg.cfg_search_radius_0 | NFZ search radius, lower is less enforcement | + | ^ airport_limit_cfg.cfg_search_radius_0 | NFZ search radius, lower is less enforcement| |
^ airport_limit_cfg.cfg_disable_airport_fly_limit_0|Disable NFZ| | ^ airport_limit_cfg.cfg_disable_airport_fly_limit_0|Disable NFZ| | ||
- | ^ airport_limit_cfg.cfg_limit_data_0 | NFZ map data value | + | ^ airport_limit_cfg.cfg_limit_data_0 | NFZ map data value| |
- | ^ airport_limit_cfg.cfg_enable[FLY_LIMIT_TYPE_SPECIAL]_0 | NFZ Type 2 Removal (GeoZone) | + | ^ airport_limit_cfg.cfg_enable[FLY_LIMIT_TYPE_SPECIAL]_0 | NFZ Type 2 Removal (GeoZone)| |
^ flying_limit.auto_landing_enabled_0|No landing at 65k feet from HP| | ^ flying_limit.auto_landing_enabled_0|No landing at 65k feet from HP| | ||
^ voltage.level_1_protect_type_0|Battery level 1 function (warn, led)| | ^ voltage.level_1_protect_type_0|Battery level 1 function (warn, led)| | ||
Line 132: | Line 133: | ||
^ voltage2.user_set_smart_bat_0|Battery type (DJI vs non-DJI)| | ^ voltage2.user_set_smart_bat_0|Battery type (DJI vs non-DJI)| | ||
^ voltage2.level2_smart_battert_land_0|SmartRTH battery landing %| | ^ voltage2.level2_smart_battert_land_0|SmartRTH battery landing %| | ||
+ | ^ advanced_function.driver_license_limit_enable_0|DJI Driver License Pilot| | ||
+ | ^ advanced_function.viechle_license_limit_enable_0|DJI Driver License Aircraft| | ||
====== Parameter Values to Change ====== | ====== Parameter Values to Change ====== | ||
I removed the g_config from the prefix to make the table fit better :) | I removed the g_config from the prefix to make the table fit better :) |