howto:modp3params
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision Last revision Both sides next revision | ||
|
howto:modp3params [2019/07/21 23:20] digdat0 rewrote install steps |
howto:modp3params [2019/07/21 23:32] digdat0 drivers license parms |
||
|---|---|---|---|
| Line 94: | Line 94: | ||
| | | ||
| - | |||
| - | This will recompile the modified firmware module, which will allow it to be installed onto the aircraft. You can now update the aircraft with this firmware file. | ||
| - | To install | + | * After this command runs, it will compile the parameters back into the P3X_FW_V01.07.0060_m0306.bin file. |
| + | * Now, you need to rename the file before loading | ||
| - | 1. Rename the modified file P3X_FW_V01.07.0060_m0306.bin | ||
| - | p3 = PMCAPPFw3.bin | ||
| - | I1 = INMCAPPFw1.bin | ||
| - | 2. Copy the file to your SD card. Put SD card into the aircraft. | ||
| - | 3. Power on the aircraft. Update will start in about 30 seconds. You will hear a distinct noise during the update process, which will change when done. It should take 3-5 minutes. | ||
| - | ** If the update does not start, please turn off aircraft. Press and hold the bind button, and turn back on. Hold this button for 20-30 seconds and the update will start and will make a beeping noise, then you can let go and let the update finish. | ||
| - | |||
| - | 4. When update is done, power off the aicraft. Remove the SD card from the camera and back into the computer | ||
| - | 5. Remove/ Delete the " | ||
| - | Note: If the file is " | ||
| - | 6. Put Sd card back in the camera | ||
| - | |||
| - | All done! On your next startup, the modifications will persist on the aircraft. They will remain until you reflash the stock firmware. | ||
| - | |||
| - | Note: If your firmware is version 01.04 or earlier, you may need to rename the file MCAPPFw.bin instead. | ||
| ==== 4. Install the modded file on your Phantom ==== | ==== 4. Install the modded file on your Phantom ==== | ||
| - | * To install the file on your Phantom, copy the PMCAPPFw3.bin file to a formatted micro-SD card | + | * To install the file on your aircraft, copy the PMCAPPFw3.bin or INMCAPPFw1.bin file to a formatted micro-SD card |
| * Insert SD card into aircraft, power on. If the firmware update does not start, you can force it by holding the button on the side of the VPS. | * Insert SD card into aircraft, power on. If the firmware update does not start, you can force it by holding the button on the side of the VPS. | ||
| * The file will be flashed and the edited parameters will be applied. | * The file will be flashed and the edited parameters will be applied. | ||
| Line 149: | Line 133: | ||
| ^ voltage2.user_set_smart_bat_0|Battery type (DJI vs non-DJI)| | ^ voltage2.user_set_smart_bat_0|Battery type (DJI vs non-DJI)| | ||
| ^ voltage2.level2_smart_battert_land_0|SmartRTH battery landing %| | ^ voltage2.level2_smart_battert_land_0|SmartRTH battery landing %| | ||
| + | ^ advanced_function.driver_license_limit_enable_0|DJI Driver License Pilot| | ||
| + | ^ advanced_function.viechle_license_limit_enable_0|DJI Driver License Aircraft| | ||
| ====== Parameter Values to Change ====== | ====== Parameter Values to Change ====== | ||
| I removed the g_config from the prefix to make the table fit better :) | I removed the g_config from the prefix to make the table fit better :) | ||
| - | Last edit: digdat0 | + | Last edit: digdat0 |
| **Height Limit Removal** | **Height Limit Removal** | ||
| Line 188: | Line 174: | ||
| ^ voltage2.user_set_smart_bat_0 | 0 | 10 | 2 | 0 | 0 | 0 | | ^ voltage2.user_set_smart_bat_0 | 0 | 10 | 2 | 0 | 0 | 0 | | ||
| ^ voltage2.level2_smart_battert_land_0 | 0 | 100 | 10 | 0 | 0 | 0 | | ^ voltage2.level2_smart_battert_land_0 | 0 | 100 | 10 | 0 | 0 | 0 | | ||
| + | **Disable DJI's driver license enforcement** | ||
| + | ^ Parameter Name ^ Stock minValue ^ Stock MaxValue ^ Stock defaultValue ^ New MinValue ^ new Maxvalue ^ New defaultValue ^ | ||
| + | ^ advanced_function.driver_license_limit_enable_0 | 1 | 1 | 1 | 2 | 2 | 2 | | ||
| + | ^ advanced_function.viechle_license_limit_enable_0 | 1 | 1 | 1 | 2 | 2 | 2 | | ||
| ===== All Parameters Lists ===== | ===== All Parameters Lists ===== | ||
| * [[howto: | * [[howto: | ||
howto/modp3params.txt · Last modified: 2019/07/21 23:35 by digdat0
Page Tools
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Noncommercial-Share Alike 4.0 International
