This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision Last revision Both sides next revision | ||
howto:modp3params [2019/07/21 23:24] digdat0 restored |
howto:modp3params [2019/07/21 23:32] digdat0 drivers license parms |
||
---|---|---|---|
Line 96: | Line 96: | ||
* After this command runs, it will compile the parameters back into the P3X_FW_V01.07.0060_m0306.bin file. | * After this command runs, it will compile the parameters back into the P3X_FW_V01.07.0060_m0306.bin file. | ||
- | * Now, you need to rename the file before loading on the aircraft. Rename it to " | + | * Now, you need to rename the file before loading on the aircraft. Rename it to " |
- | * For Inspire1 rename it to " | + | |
==== 4. Install the modded file on your Phantom ==== | ==== 4. Install the modded file on your Phantom ==== | ||
- | * To install the file on your Phantom, copy the PMCAPPFw3.bin file to a formatted micro-SD card | + | * To install the file on your aircraft, copy the PMCAPPFw3.bin or INMCAPPFw1.bin file to a formatted micro-SD card |
* Insert SD card into aircraft, power on. If the firmware update does not start, you can force it by holding the button on the side of the VPS. | * Insert SD card into aircraft, power on. If the firmware update does not start, you can force it by holding the button on the side of the VPS. | ||
* The file will be flashed and the edited parameters will be applied. | * The file will be flashed and the edited parameters will be applied. | ||
Line 133: | Line 133: | ||
^ voltage2.user_set_smart_bat_0|Battery type (DJI vs non-DJI)| | ^ voltage2.user_set_smart_bat_0|Battery type (DJI vs non-DJI)| | ||
^ voltage2.level2_smart_battert_land_0|SmartRTH battery landing %| | ^ voltage2.level2_smart_battert_land_0|SmartRTH battery landing %| | ||
+ | ^ advanced_function.driver_license_limit_enable_0|DJI Driver License Pilot| | ||
+ | ^ advanced_function.viechle_license_limit_enable_0|DJI Driver License Aircraft| | ||
====== Parameter Values to Change ====== | ====== Parameter Values to Change ====== | ||
I removed the g_config from the prefix to make the table fit better :) | I removed the g_config from the prefix to make the table fit better :) | ||
- | Last edit: digdat0 | + | Last edit: digdat0 |
**Height Limit Removal** | **Height Limit Removal** | ||
Line 172: | Line 174: | ||
^ voltage2.user_set_smart_bat_0 | 0 | 10 | 2 | 0 | 0 | 0 | | ^ voltage2.user_set_smart_bat_0 | 0 | 10 | 2 | 0 | 0 | 0 | | ||
^ voltage2.level2_smart_battert_land_0 | 0 | 100 | 10 | 0 | 0 | 0 | | ^ voltage2.level2_smart_battert_land_0 | 0 | 100 | 10 | 0 | 0 | 0 | | ||
+ | **Disable DJI's driver license enforcement** | ||
+ | ^ Parameter Name ^ Stock minValue ^ Stock MaxValue ^ Stock defaultValue ^ New MinValue ^ new Maxvalue ^ New defaultValue ^ | ||
+ | ^ advanced_function.driver_license_limit_enable_0 | 1 | 1 | 1 | 2 | 2 | 2 | | ||
+ | ^ advanced_function.viechle_license_limit_enable_0 | 1 | 1 | 1 | 2 | 2 | 2 | | ||
===== All Parameters Lists ===== | ===== All Parameters Lists ===== | ||
* [[howto: | * [[howto: |